A: Trial 1, because the average rate of the reaction is lower.
The rate of reaction is the speed with which reactants are converted into products. It is also the rate at which reactants disappear and products appear. The higher the rate of reaction, the greater the amount of product formed in a reaction.
If we look at the graph, we will realize that trial 1 produces a lesser amount of product than trial 2. This implies that the average rate of the reaction in trial 1 is lower than in trial 2.
Lower average rate of reaction implies lower concentration of the reactants since the rate of reaction depends on the concentration of reactants.
Hence trial 1 has a lower concentration of reactants because the average rate of the reaction is lower.
Answer:
D. ionic sodium phosphate (Na3PO4)
Explanation:
Molecule for molecule, the solute that raises the boiling point of water the most is the one that makes the most particles in the solution. Lithium chloride breaks up into two ions (Li+ and Cl-). So does sodium chloride (Na+ and Cl-). Molecular molecules don't break up at all, so sucrose has only 1 particle per molecule. Sodium phosphate makes 4 total particles (3 Na+ ions and 1 PO4^3-). And magnesium bromide would make 3 particles (1 Mg2+ and 2 Br-). So the most is 4.
Answer:
0.544 M
Explanation:
First find the moles in the final solution
0.8 mols/L *1.7L
1.36 mols
so there is 1.36 mols in 2.5L
concentration will be 1.36/2.5
0.544 M
Answer:
They are emitted from heated objects
Explanation:
When objects are heated, they emit light at all wavelengths thereby forming a continuous spectrum. Electromagnetic radiation of all wavelengths and colours are usually represented in such spectrum. A thermal spectrum is quite a simple spectrum since it depends on temperature.
<span>1 trial : you have nothing to compare the result with - you don't know if it's a mistake.
2 trials : you can compare results - if very different, one may have gone wrong, but which one?
3 trials : if 2 results are close and 3rd far away, 3rd probably unreliable and can be rejected.
******************************
First calculate the enthalpy of fusion. M, C and m,c = mass and
specific heat of calorimeter and water; n, L = mass and heat of fusion
of ice; T = temperature fall.
L = (mc+MC)T/n.
c=4.18 J/gK. I assume calorimeter was copper, so C=0.385 J/gK.
1. M = 409g, m = 45g. T = 22c, n = 14g
L = (45*4.18+409*0.385)*22/14 = 543.0 J/g.
2. M = 409g, m = 49g, T = 20c, n = 13g
L = (49*4.18+409*0.385)*20/13 = 557.4 J/g.
3. M = 409g, m = 54g, T = 20c, n = 14g
L = (54*4.18+409*0.385)*20/14 = 547.4 J/g.
(i) Estimate error in L from spread of 3 results.
Average L = 549.3 J/g.
average of squared differences (variance) = (6.236^2+8.095^2+1.859^2)/3 = 35.96
standard deviation = 5.9964
standard error = SD/(N-1) = 5.9964/2 = 3 J/g approx.
% error = 3/547 x 100% = 0.5%.
(ii) Estimate error in L from accuracy of measurements:
error in masses = +/-0.5g
error in T = +/-0.5c
For Trial 3
M = 409g, error = 0.5g
m = 463-409, error = sqrt(0.5^2+0.5^2) = 0.5*sqrt(2)
n =(516-463)-(448-409)=14, error = 0.5*sqrt(4) = 1.0g
K = (mc+MC)=383, error = sqrt[2*(0.5*4.18)^2+(0.5*0.385)^2] = 2.962
L = K*T/n
% errors are
K: 3/383 x 100% = 0.77
T: 0.5/20 x 100% = 2.5
n: 1.0/14 x 100% = 7.14
% errors in K and T are << error in n, so we can ignore them.
% error in L = same as in n = 7% x 547.4 = 40 (always round final error to 1 sig fig).
*************************************
The result is (i) L= 549 +/- 3 J/g or (ii) L = 550 +/- 40 J/g.
Both are very far above accepted figure of 334 J/g, so there is at least
one systematic error in the experiment or the calculations.
eg calorimeter may not be copper, so C is not 0.385 J/gK. (If it was
polystyrene, which absorbs/ transmits little heat, the effective value
of C would be very low, reducing L.)
Using +/- 40 is probably best (more cautious).
However, the spread in the actual results is much smaller; try to explain this discrepancy - eg
* measurements were "fiddled" to get better results; other Trials were made but only best 3 were chosen.
* measurements were more accurate than I assumed (eg masses to nearest 0.1g but rounded to 1g when written down).
Other sources of error:
L=(mc+MC)T/n is too high, so n (ice melted) may be too small, or T (temp fall) too high - why?
* it is suspicious that all final temperatures were 0c - was this
actually measured or just guessed? a higher final temp would reduce L.
* we have assumed initial and final temperature of ice was 0c, it may
actually have been colder, so less ice would melt - this could explain
small values of n
* some water might have been left in container when unmelted ice was
weighed (eg clinging to ice) - again this could explain small n;
* poor insulation - heat gained from surroundings, melting more ice,
increasing n - but this would reduce measured L below 334 J/g not
increase it.
* calorimeter still cold from last trial when next one started, not
given time to reach same temperature as water - this would reduce n.
Hope This Helps :)
</span>
