The mass of solute per 100 mL of solution is abbreviated as (m/v). Mass is not technically the same thing as weight, but the abbreviation (w/v) is also common. 262 grams of sucrose are needed to make 655 mL of a 40.0% (w/v) sucrose solution
<h3>Define Solute</h3>
A solute is a material that dissolves in a solution. The amount of solvent present in fluid solutions is greater than the amount of solute. The two most common examples of solutions in daily life are salt and water. Salt is the solute because it dissolves in water.
<h3>forms of ratios for product concentration or yield:-</h3>
- w/v:- Weight by volume or weight per volume are the terms used. Any solid compound's concentration in a liquid can be calculated using it. It is measurable in gm/ml.
- Weight by weight ratio is referred to as w/w.It is employed to determine the final yield of the compound obtained from the starting compound. as in —mg/—gm.
It provides the real yield of the substance or item.
- Volume/volume. It is used to specify a liquid's composition or percent in a liquid compound.
using w/v we can calculate the weight of sucrose:-
40.0% means 40 g sucrose/ 100 g solution
40.0g sucrose x (655/100)=grams of sucrose
262 grams of sucrose are needed to make 655 mL of a 40.0% (w/v) sucrose solution.
Learn more about Solute here:-
brainly.com/question/14397121
#SPJ4
Answer:
M
Explanation:
Henry's law relational the partial pressure and the concentration of a gas, which is its solubility. So, at the sea level, the total pressure of the air is 1 atm, and the partial pressure of O2 is 0.21 atm. So 21% of the air is O2.
Partial pressure = Henry's constant x molar concentration
0.21 = Hx1.38x
H =
H = 152.17 atm/M
For a pressure of 665 torr, knowing that 1 atm = 760 torr, so 665 tor = 0.875 atm, the ar concentration is the same, so 21% is O2, and the partial pressure of O2 must be:
P = 0.21*0.875 = 0.1837 atm
Then, the molar concentration [O2], will be:
P = Hx[O2]
0.1837 = 152.17x[O2]
[O2] = 0.1837/15.17
[O2] = M
Answer:
Computer, Microprocessor, Cell Phone, WWW, iPhone
Explanation:
i just did it and got it correct
Answer:
we only see parts of the lit side as the moon goes around the earth
Explanation:
Unlike the sun, the moon orbits the Earth. This is the reason why we see the <em>different phases of the moon.</em> The reflection of the moon is being illuminated back to us with the help of the sun. So, as the moon circles the Earth, we only see parts of the lit side. Such changes helps us see the moon in different phases such as<em> </em>the <em>Third Quarter, Crescent, New Moon, Full Moon, etc.</em>
For example, during "Full Moon," <em>the moon's entire face is lit up by the sun</em>. Thus, we see the entire moon's lit portion.
Thus, this explains the answer.
First, consider the steps to heat the sample from 209 K to 367K.
1) Heating in liquid state from 209 K to 239.82 K
2) Vaporaizing at 239.82 K
3) Heating in gaseous state from 239.82 K to 367 K.
Second, calculate the amount of heat required for each step.
1) Liquid heating
Ammonia = NH3 => molar mass = 14.0 g/mol + 3*1g/mol = 17g/mol
=> number of moles = 12.62 g / 17 g/mol = 0.742 mol
Heat1 = #moles * heat capacity * ΔT
Heat1 = 0.742 mol * 80.8 J/mol*K * (239.82K - 209K) = 1,847.77 J
2) Vaporization
Heat2 = # moles * H vap
Heat2 = 0.742 mol * 23.33 kJ/mol = 17.31 kJ = 17310 J
3) Vapor heating
Heat3 = #moles * heat capacity * ΔT
Heat3 = 0.742 mol * 35.06 J / (mol*K) * (367K - 239.82K) = 3,308.53 J
Third, add up the heats for every steps:
Total heat = 1,847.77 J + 17,310 J + 3,308.53 J = 22,466.3 J
Fourth, divide the total heat by the heat rate:
Time = 22,466.3 J / (6000.0 J/min) = 3.7 min
Answer: 3.7 min