An electromagnet is a solenoid with a piece of ferromagnetic material within it.

A loop of wire is in a magnetic field such that its axis is parallel with the field direction. Which of the following would resu

ahrayia [7]

Answer:

All the given options will result in an induced emf in the loop.

Explanation:

The induced emf in a conductor is directly proportional to the rate of change of flux.

$emf = -\frac{d \phi}{dt} \\\\where;\\\\\phi \ is \ magnetic \ flux\\\\\phi = BA\ cos \theta$

where;

A is the area of the loop

B is the strength of the magnetic field

θ is the angle between the loop and the magnetic field

Considering option A, moving the loop outside the magnetic field will change the strength of the magnetic field and consequently result in an induced emf.

Considering option B, a change in diameter of the loop, will cause a change in the magnetic flux and in turn result in an induced emf.

Option C has a similar effect with option A, thus both will result in an induced emf.

Finally, considering option D, spinning the loop such that its axis does not consistently line up with the magnetic field direction will change the angle between the loop and the magnetic field. This effect will also result in an induced emf.

Therefore, all the given options will result in an induced emf in the loop.

4 0

2 years ago

The heat energy gained by the water in one minute is ?

kari74 [83]

fast-moving particles colliding with slow-moving particles

7 0

2 years ago

The constant forces F1 = 8 + 29 + 32 N and F2 = 48 - 59 - 22 N act together on a particle during a displacement from the point A

steposvetlana [31]

Answer:

- 600 J

Explanation:

A (20, 15, 0 ) m

B (0, 0, 7) m

$\overrightarrow{F_{1}}=8\widehat{i}+29\widehat{j}+32\widehat{k}$

$\overrightarrow{F_{2}}=48\widehat{i}-59\widehat{j}-22\widehat{k}$

Net force

$\overrightarrow{F}=\overrightarrow{F_{1}}+\overrightarrow{F_{2}}$

$\overrightarrow{F}}=\left ( 8+48 \right )\widehat{i}+\left ( 29-59 \right )\widehat{j}+\left ( 32-22 \right )\widehat{k}$

$\overrightarrow{F}}=56\widehat{i}-30\widehat{j}+10\widehat{k}$

$\overrightarrow{S}=\overrightarrow{OB}-\overrightarrow{OA}$

$\overrightarrow{S}=\left ( 0-20 \right )\widehat{i}+\left ( 0-15 \right )\widehat{j}+\left ( 7-0 \right )\widehat{k}$

$\overrightarrow{S}=-20\widehat{i}-15\widehat{j}+7\widehat{k}$

Work done is defined as

$W = \overrightarrow{F}.\overrightarrow{S}$

$W = \left ( 56\widehat{i}-30\widehat{j}+10\widehat{k} \right ).\left (-20\widehat{i}-15\widehat{j}+7\widehat{k} \right )$

W = -1120 + 450 + 70

W = - 600 J

3 0

2 years ago

A ramp that is 8 meters long raises an object 2meters. What is the mechanical advantage

Masteriza [31]

10m long is the right answer or 16

5 0

2 years ago

A solid concrete block weighs 150. N and is resting on the ground. Its dimensions are 0.400 m ✕ 0.200 m ✕ 0.100 m. A number of i

N76 [4]

Answer:

27 blocks

Explanation:

First, the expression to use here is the following:

P = F/A

Where:

P: pressure

F: Force exerted

A: Area of the block.

Now , we need to know the number of blocks needed to exert a pressure that equals at least 2 atm. To know this, we should rewrite the equation. We know that certain number of blocks, with the same weight and dimensions are putting one after one over the first block, so we can say that:

P = W/A

P = n * W1 / A

n would be the number of blocks, and W1 the weight of the block.We have all the data, and we need to calculate the area of the block which is:

A = 0.2 * 0.1 = 0.02 m²

Solving now for n:

n = P * A / W1

The pressure has to be expressed in N/m²

P = 2 atm * 1.01x10^5 N/m² atm = 2.02x10^5 N/m²

Finally, replacing all data we have:

n = 2.02x10^5 * 0.02 / 150

n = 26.93

We can round this result to 27. So the minimum number of blocks is 27.

5 0

2 years ago