What word describes the position in the moon's elliptical orbit when it is closest to Earth?

A golf ball stays on the tee until the golf club hits it. Which of the following principles best describes why this occurs? Grou

givi [52]

Answer:

Newton's First Law of Motion.

Explanation:

Newton's first law of motion states that an object continues to stay in its state of rest, or of uniform motion, until acted upon by an external force.

So in the case of the golf ball here, the ball stays in its state of rest, on the tee, until the golf club hits it, i.e. , applies an external force on it.

Hence we can say that Newton's First Law of Motion is the principle which is most suitable for explaining this phenomenon.

7 0

3 years ago

I WILL GIVE BRAINLIEST IF SOMEONE GETS THIS......

pav-90 [236]

Answer:

Explanation:

a)

Firstly to calculate the total mass of the can before the metal was lowered we need to add the mass of the eureka can and the mass of the water in the can. We don't know the mass of the water but we can easily find if we know the volume of the can. In order to calculate the volume we would have to multiply the area of the cross section by the height. So we do the following.

100 $cm^{2}$ x 10cm = 1000 $cm^{3}$

Now in order to find the mass that water has in this case we have to multiply the water's density by the volume, and so we get....

$\frac{1g}{cm^{3} }$ x 1000 $cm^{3}$ = 1000g or 1kg

Knowing this, we now can calculate the total mass of the can before the metal was lowered, by adding the mass of the water to the mass of the can. So we get....

1000g + 100g = 1100g or 1.1kg

b)

The volume of the water that over flowed will be equal to the volume of the metal piece (since when we add the metal piece, the metal piece will force out the same volume of water as itself, to understand this more deeply you can read the about "Archimedes principle"). Knowing this we just have to calculate the volume of the metal piece an that will be the answer. So this time in order to find volume we will have to divide the total mass of the metal piece by its density. So we get....

20g ÷ $\frac{8g}{cm^{3} }$ = 2.5 $cm^{3}$

c)

Now to find out the total mass of the can after the metal piece was lowered we would have to add the mass of the can itself, mass of the water inside the can, and the mass of the metal piece. We know the mass of the can, and the metal piece but we don't know the mass of the water because when we lowered the metal piece some of the water overflowed, and as a result the mass of the water changed. So now we just have to find the mass of the water in the can keeping in mind the fact that 2.5 $cm^{3}$ overflowed. So now we the same process as in number a) just with a few adjustments.

$\frac{1g}{cm^{3} }$ x (1000 $cm^{3}$ - 2.5 $cm^{3}$ ) = 997.5g

So now that we know the mass of the water in the can after we added the metal piece we can add all the three masses together (the mass of the can. the mass of the water, and the mass of the metal piece) and get the answer.

100g + 997.5g + 20g = 1117.5g or 1.1175kg

5 0

2 years ago

6 use superposition to find voltage v(t) across the 100 ohm resistor

Vinvika [58]

It'll be my pleasure to analyze the circuit, describe my analysis in detail,
and give you a clear, precise, and accurate answer.

As soon as you let me see the circuit diagram, with values marked on
all of its components and power sources.

6 0

2 years ago

The gravitational force between the charged constituents of the atom is negligible compared with the electric force between them

katrin2010 [14]

Answer: The initial force is reduced a factor 1/4 when the separation between charge is doubled

Explanation: As it well known the electric force between two charges is given by:

Finitial=k*q1*q2/d^2 where d is the distance between charges and k is a constant

if the distance is doubled this means 2*dinitial thus the new force is equal to F initial* 1/4

6 0

2 years ago

Consider the free-body diagram. If you want the box to move, the force applied while dragging must be greater than the

VLD [36.1K]

You would want it to be greater than D. friction force

It needs be greater than the friction applied to it.

6 0

2 years ago