All categories

2 years ago

What happens to kinetic energy when you increase the mass?

Physics

1 answer:

Rus_ich [418]2 years ago

5 0

Increasing mass increases kinetic energy. This can be seen in the equation KE = 1/2 (m) (v)^2

If you found this helpful, please brainliest me!

You might be interested in

When you take your 1900-kg car out for a spin, you go around a corner of radius 55 m with a speed of 15 m/s. The coefficient of

pentagon [3]

Answer:

7772.72N

Explanation:

When u draw your FBD, you realize you have 3 forces (ignore the force the car produces), gravity, normal force and static friction. You also realize that gravity and normal force are in our out of the page (drawn with a frame of reference above the car). So that leaves you with static friction in the centripetal direction.

Now which direction is the static friction, assume that it is pointing inward so

Fc=Fs=mv²/r=1900*15²/55=427500/55=7772.72N

Since the car is not skidding we do not have kinetic friction so there can only be static friction. One reason we do not use μFn is because that is the formula for maximum static friction, and the problem does not state there is maximum static friction.

7 0

2 years ago

Which of the following shows kinetic energy being converted into potential energy?

Komok [63]

B) a rock being tossed high into the air

3 0

2 years ago

A group of letters used at the start of a word to change its meaning?

Diano4ka-milaya [45]

Answer:

prefix

Explanation:

6 0

2 years ago

How does the period affects the centripetal force?

Anna71 [15]

Answer:According to the Equation (2), centripetal force is proportional to the square of the speed for an object of given mass M rotating in a given radius R.

Explanation:The Period T. The time T required for one complete revolution is called the period. For. constant speed. v = 2π r T holds.

8 0

2 years ago

Read 2 more answers

Steam is to be condensed on the shell side of a heat exchanger at 150 oF. Cooling water enters the tubes at 60 oF at a rate of 4

zalisa [80]

Answer:

a. 572Btu/s

b.0.1483Btu/s.R

Explanation:

a.Assume a steady state operation, KE and PE are both neglected and fluids properties are constant.

From table A-3E, the specific heat of water is $c_p=1.0\ Btu/lbm.F$ , and the steam properties as, A-4E:

$h_{fg}=1007.8Btu/lbm, s_{fg}=1.6529Btu/lbm.R$

Using the energy balance for the system:

$\dot E_{in}-\dot E_{out}=\bigtriangleup \dot E_{sys}=0\\\\\dot E_{in}=\dot E_{out}\\\\\dot Q_{in}+\dot m_{cw}h_1=\dot m_{cw}h_2\\\\\dot Q_{in}=\dot m_{cw}c_p(T_{out}-T_{in})\\\\\dot Q_{in}=44\times 1.0\times (73-60)=572\ Btu/s$

Hence, the rate of heat transfer in the heat exchanger is 572Btu/s

b. Heat gained by the water is equal to the heat lost by the condensing steam.

-The rate of steam condensation is expressed as:

$\dot m_{steam}=\frac{\dot Q}{h_{fg}}\\\\\dot m_{steam}=\frac{572}{1007.8}=0.5676lbm/s$

Entropy generation in the heat exchanger could be defined using the entropy balance on the system:

$\dot S_{in}-\dot S_{out}+\dot S_{gen}=\bigtriangleup \dot S_{sys}\\\\\dot m_1s_1+\dot m_3s_3-\dot m_2s_2-\dot m_4s_4+\dot S_{gen}=0\\\\\dot m_ws_1+\dot m_ss_3-\dot m_ws_2-\dot m_ss_4+\dot S_{gen}=0\\\\\dot S_{gen}=\dot m_w(s_2-s_1)+\dot m_s(s_4-s_3)\\\\\dot S_{gen}=\dot m c_p \ In(\frac{T_2}{T_1})-\dot m_ss_{fg}\\\\\\\dot S_{gen}=4.4\times 1.0\times \ In( {73+460)/(60+460)}-0.5676\times 1.6529\\\\=0.1483\ Btu/s.R$

Hence,the rate of entropy generation in the heat exchanger. is 0.1483Btu/s.R

4 0

2 years ago